/ We will do attentively..   Collection / Supposes / E-mail / Site map
Warm congratulation NINGBO CIE INDUSTRY AND TRADE CO.,LTD website clear~
 Product List

Auto Bearings


Front Wheel Hub Bearings
  Rear Wheel Hub Bearings
 

Tensioner&Idler Bearings

 

Clutch Release Bearings

 

Wheel Hub Bearing(One Generation)

 

Wheel Hub Bearing( second generation)

 

Wheel Hub Bearing ABS System

 

Water Pump Bearing

 

Automotive Tapered Roller Bearings

 

Steering Wheel Bearings

 

Universal Joint Kits

    Automobile Center Support Bearing
  Steering Gear Box Bearings
  Special Non Standard Auto Bearing
  Automobile Alternator Bearing
  Automotive Air Condition Bearings

Industry Bearing


Deep Groove Ball Bearings
  Angular Contact Ball Bearing
 

Cylindrical Roller Bearings

 

Self-Aligning Ball Bearing

 

Spherical Roller Bearings

 

Tapered Roller Bearings

 

Bearing Units

 

Thrust Bearings

 

Needle Roller Bearings

 

Linear Bearings

 

Special Non Standard bearings

Power Transmission Parts


Ball leading Screw

 

Linear Motion Shaft

  Linear Guide Rail and Block Assemblies
  Precise Crossing Guide Rail

Auto Steering Gears


Worm and level Steering Gears

 

Rack and Pinion Type Steering Gears

 

Recirculating Ball Type Steering Gears


  Bearing Technology

Bearing Material Retainer (cage) Closures Load Rating Radial Play
Maximum Speed Shaft/housing fit Tolerance Frictional Torque Noise Rating Lubricants

10. Noise Rating

Bearing rings and balls are not perfectly round and the balls and raceways, even after extensive fine grinding and polishing, are not perfectly smooth. There are machining imperfections in the form of rough or uneven surfaces. For example, if a bearing inner ring is rotating and the outer ring fixed, these imperfections will cause the outer ring to move radially in relation to the inner ring. The amount and speed of this movement contributes to the amount of bearing vibration and noise. Poor cage design can also increase bearing noise.

The smoothness or quietness of a bearing can be checked by accelerometers which measure vibration at the outer ring of a bearing, usually with the inner ring rotating at 1800 rpm. To understand how bearing vibration is measured, it is important to understand how vibration works. When measuring bearing vibration, we need to take into account both displacement and frequency as these two factors together tell us far more.
Firstly, a vibrating object moves or oscillates. This amount of movement is called displacement. When (for example) a bearing outer ring vibrates, the outer surface will move upwards to the upper limit, then down to the lower limit and then back to the start point. The measurement between upper and lower limit is called peak to peak displacement. The whole oscillation movement from start point through upper and lower limits and back to start point is called a cycle. This vibration cycle will repeat as long as the bearing is rotating. We can also measure the number of these cycles in a given time. This gives us the frequency. Frequency is most commonly expressed as cycles per second (CPS) or Hertz (Hz) which is the same thing.
Vibration is potentially damaging to a bearing and the equipment it is used in, increasing the rate of fatigue and therefore, shortening the life of the bearing. Displacement measurements do not tell us enough. Vibration in a bearing or a machine will usually occur at many different frequencies and they all contribute to fatigue so we need to take all of these frequencies of vibration into account in our measurements of vibration. We can achieve this by measuring vibration velocity.

Vibration velocity is displacement x frequency. If a bearing component is moving a particular distance (displacement) at a particular rate (frequency) it must be moving at a certain speed. Vibration velocity gives us a much better indication of how severe the vibration is. The higher the vibration velocity measurement, the noisier the bearing and the faster the bearing will fail as a result of fatigue. Vibration velocity is measured on a BVT machine (Bearing Vibration Tester) in microns per second or an Anderon Meter in Anderons. One Anderon equals 7.5 microns per second. The vibration velocity readings are separated into three frequency bands:
Low band (50 to 300 Hz); Medium band (300 to 1800 Hz); High Band (1800 to 10000 Hz)
These vibration velocity measurements are usually classified into V grades (e.g. V1, V2, V3 or V4). Although vibration velocity measures the fatigue potential, this is not the only cause of failure. Vibration force can cause deformation to balls and rings. Vibratory force can be very damaging at high frequencies where velocity readings may be quite low. For this reason we also measure vibration acceleration.
Vibration acceleration is an indication of vibratory force (force = mass x acceleration) and since force is damaging at higher frequencies, vibration acceleration is a useful measurement where a bearing will experience vibration frequencies above 2000 Hz. Vibration acceleration is measured in G (1G being the acceleration produced by the Earth's gravity or 9.81 m/s²) but you will often see these measurements converted to decibels (dB). These decibel measurements are usually classified into Z grades (Z1, Z2, Z3 or Z4). Bearings can be classified according to both vibration velocity AND vibration acceleration levels (ZV1, ZV2, ZV3 or ZV4).
A low noise/vibration rating is achieved by paying particular attention to the surface finish of the raceways and balls, the roundness of the rings and balls and correct cage design. We have three ratings for low noise bearings: EMQ (ZV2), EMQ2 (ZV3) and the quietest, EMQ3 (ZV4). These ratings are independent of precision grade, for example, a P6 bearing may be offered with any of the three noise ratings. To help reduce noise levels even further, low noise greases are available and the choice is now greater due to improved lubricant manufacuring techniques. These greases are more finely filtered and contain fewer, smaller solid particles. These particles generate noise when they pass between the balls and raceway.
External factors such as surrounding vibration can affect bearing noise. Another problem, particularly with smaller and thin-section bearings, as mentioned in "Shaft/Housing Fits" (section 7) is ring distortion caused by poor shaft or housing roundness. Dirt or dust contamination will also increase noise and vibration levels. Poor fitting practice or incorrect handling is sometimes to blame, causing shock loads which, in turn, create scratches or dents in the raceway.




Workshop | Products | Contact  
Copyright © NINGBO CIE INDUSTRY AND TRADE CO.,LTD. All Rights Reserved. Design By HiSupplier Online Inc.